Flat Tire Repair

That tool pictured above is what you’re looking for to repair your flat tire. I literally, just used this exact tool and tire plug set over the weekend! I blew a tire way out of town. I pulled into the nearest gas station, pulled out the kit (I keep one handy in the glove box) and repaired it right there at the gas station, and I was on my way again!

You know that sinking feeling. The one that makes your stomach do a slow, backwards, somersault as a groan escapes your lips. “Ugh, my tire is flat!” Yes, a flat tire and it’s on your car, so what do you do now? Call a tow truck service so someone will come out and fix the flat for you? That isn’t going to be cheap! Take your other car and leave the flat to deal with later? You’re still going to have to take care of that flat tire sooner or later.

Read through this and you won’t have to ask these questions again, because you’ll know exactly what to do.

Repairing a flat tire, like a pro, is easy. I wouldn’t call myself a “pro”, but I worked as an automotive technician and inspector for several years. What I learned from those years is there are a whole lot of repairs the average Joe can perform that we pay mechanics a lot of money to do!

There are five easy steps to repair that flat tire. Depending on your physical agility, you can perform this repair On or Off the car! Repairing the flat on the car is the quickest, but you have to have strong arms to push the plug in. If the tire is off the car; you can put your weight on the needle tool to push it through the puncture site, but if you leave the tire on the vehicle; you only have your muscles to push the needle tool in.

The plug material is the same stuff used by mechanics to repair a puncture. It will last as long as the tire does. I’ve been using these tire repair kits for twenty years and I’ve never had a plug fail.

If you find it easier to remove the wheel from the vehicle to complete the repair steps, then by all means, remove the wheel. It won’t change anything when repairing it except you will have better leverage to work on the puncture in the tire.

Remove the wheel:

There are as many different wheel well dimensions as there are vehicles on the road, so depending on what kind of vehicle has the flat, will dictate whether you must remove the tire. The position of the foreign object in the tire will also determine whether the tire must be removed. The tire can be left on for the repair if:

  • There is a gap between the tire and the wheel well that you can get your arm into.
  • It is parked on a level service where rolling won’t be an issue.
  • Looking at the width of the tire, the puncture is no more than mid-way of the tire. Any further in and it becomes too much of an odd angle to push the reamer and plug into the tire.

Remove the Wheel (optional)

  1. Chock the tires (Choking = block a tire with an object to make it stable; block).
  2. Loosen the lug nuts with a breaker bar. Just a 1/4 turn or less is fine for now on each lug nut.
  3. Position your jack under a part of the vehicle that is the frame. Do not use the jack on area’s like the springs or on shock absorber or the body (IE: door panels, fender, etc.).
  4. Raise the vehicle with a jack.
  5. Remove the lug nuts and set aside somewhere safe.
  6. Remove the tire.
  7. Follow the steps in reverse to replace the wheel.

Locate the Cause Of the Flat

If you removed the tire, roll it until you see what is stuck in it.

If you left it on the vehicle roll the car forward (or backward), until you can see it. If you cannot locate the object by looking at it, then put a good deal of soap on a washcloth or spritzer bottle and add water. Run the cloth all over the surface of the tire or spritz it heavily. After a minute or so, where ever the puncture is a bubble will appear or a bunch of small bubbles will be in one spot.

Now that you have the location of the foreign object:

  1. Using a pair of wire cutters or a similar tool, remove the object.
  2. Take the rasp tool and stick it into the hole wear the object had been and ream it out a few times.
  3. Thread a piece of the plug material onto the needle tool.
  4. Place the tip of the needle tool into the hole and push the plug material in until just about an inch is hanging out.
  5. Pull the needle tool out.

Your done!

Leave a Reply

Your email address will not be published. Required fields are marked *

12 − nine =